Joto-Vent Ventilation Flashing VIP Flashing
(Ventilation and Insect Prevention)

How to Handle Joto-Vent

Operating temperature of Joto-Vent: -22 °F to 176 °F (= -30 °C to +80 °C)
Sill plate that Joto-Vent is applied: KP-L 102U is for 204, and KP-L 150U is for 206.

CAUTION

(1)  Don't keep the product under a high or low temperature or outdoors since there is a possibility of causing a deformation.
(2)  Don't use chemical treatment woods containing copper, lead, etc. and fire prevention woods when using Joto-Vent-System.
Pay special attention to this caution.

Working Instructions for Joto-Vent

(1)  Install Joto-Vent aligning to the product side (outside) and the concrete foundation side.
(2)  Install Joto-Vent continuously so that there may be no gap at both the straight-line part and the corner part.
(3)  After confirming that Joto-Vent is installed at the concrete foundation top end with no gap, cover the sill plate
aligning to the indoor side of Joto-Vent and connect it with the concrete foundation by anchor bolts, washers, and nuts.

NOTICE

(1)  When an anchor bolt interferes with a Cross Member of Joto-Vent, interchange the right with the left of Joto-Vent,
and then make the installation so that Joto-Vent may not interfere with the anchor bolt.
(2)  You must not process Joto-Vent except for cutting made for length adjustment.
(3)  You can cut Joto-Vent freely for length adjustment; however, be sure to
leave two or more Cross Members whenusing it as the minimum size.
(4)  You must not fix the lower end of OSB or the plywood at a point lower than the upper end of Joto-Vent.
UP

Working Instructions for Ventilation Flashing and Ventilation and
Insect Prevention Flashing (VIP Flashing)

Mount Ventilation Flashing and Ventilation and Insect Prevention Flashing, which is used as required,
in accordance with the mounting dimensions in the diagrams or descriptions.

CAUTION

Don't connect Ventilation Flashing-VIP Flashing with mounting fittings and accessories which use different kind of metals,
such as copper, lead, and an alloy.

NOTICE

Fix Ventilation Flashing-VIP Flashing using stainless nails.
Remove the curing sheet attached to Ventilation Flashing immediately after construction works.

Fix Ventilation Flashing from the OSB side (outside) or the plywood with stainless nails, and its fixing interval should be within 1.5 ft. When using Ventilation Flashing, fix it at a point above the foundation top end by 2-5 / 8-inch (67 mm) while aligning the upper end of a product.

When using VIP Flashing, fix the OSB side (outside) or the plywood with stainless nails, and its fixing interval should be within 1.5 ft. Fix it at a point above the foundation top end by 2-inch (50 mm) while aligning the upper end of a product. After that, hook Ventilation Flashing on the seat of VIP Flashing, and fix it with stainless nails at the interval of within 1.5 ft. in the same manner as VIP Flashing.

NOTICE

Securely fix the lower end of the house wrap of Ventilation Flashing with the double-stick tape attached to the Flashing main body.
UP

Select a proper product according to width of Ventilation Flashing. Refer to "CAUTION" and "NOTICE" of Ventilation
Flashing for handling.

External Corner Internal Corner Middle Joiner End Cap
External Corner

This member should be fixed with stainless nails referring to the diagrams.

Internal Corner

This member should be fixed with stainless nails referring to the diagrams.

Middle Joiner

This member should be fixed with stainless nails referring to the diagrams.

End Cap

This member should be fixed with stainless nails referring to the diagrams

UP
Table of Joto-Vent System Members
contact us